How to Install a Sisal Stair Runner on Your Stairs
Sherry recently shared an Instagram Story hinting that we were back at one of our favorite projects: installing a stair runner. We first added a runner in our previous house seven years ago, and it’s stayed a go-to update because it’s accessible for most homeowners, dramatically changes the look of stairs, and adds real traction underfoot—which matters for both people and pets.

Why we wanted a stair runner
We don’t automatically cover our stairs—at our beach house we left the original wood exposed because it was charming. There, we eventually added temporary stick-on treads to help our chihuahua, Burger, get around. Here at the new house the main motivation was safety and comfort: Burger is 14 and even though he’s spry, the bare wood was slick enough that he avoided stairs unless we carried him. Adding a runner gave him the grip and confidence to trot up and down on his own again. As a bonus, the runner improved traction for us humans too.

Why we painted the stair treads
In addition to the runner, we painted the wood treads. A big reason was aesthetic: the stairs were a different wood tone than the downstairs floors, and painting the treads bridged that visual gap. The stairs also had finish issues—likely caused by paint tape applied before the floor sealer fully dried—leaving discolored lines on many steps. While a full sanding and reseal could have fixed it, most of each tread would be covered by the runner and sanding while living in the house would have been messy.

We waited a few months to be sure painting was the right choice—an important step when a change could be difficult to undo—then moved ahead because it felt right and because we wanted to make the stairs safer for Burger. In hindsight, we wish we had done it sooner; we’re thrilled with the outcome.

Prep and paint
The risers were already painted white, so we focused on the wood treads. Though the painted strip along the wall would mostly be covered by the runner, we wanted a durable floor paint. We used a porch-and-floor enamel recommended by the paint professional and chose a color that sits between gray and beige—Sherwin-Williams Requisite Gray—to visually balance the surrounding woods.

Painting was mostly careful cutting in along edges. The paint pro said a separate primer wasn’t necessary with this product, and two coats produced a solid, even finish. The result looks cleaner and ties the stairway to both the upstairs and downstairs tones.

Choosing the runner
We loved our previous striped runner for its comfort and longevity, but on a visit to friends we fell for an indoor/outdoor sisal-look runner that felt classic and durable in person. It had worn well around pets and kids and didn’t shed the way some natural sisal can. The style we chose has a natural golden-brown field with a narrow cotton border in a complementary tone, giving a polished, slightly beachy look that’s neutral enough to work with both lighter and deeper wood floors.

To size the runner, we aimed for about a 3″ reveal on each side and ordered a 25″ width. For length we measured one full “step” (tread plus riser) with a string, multiplied by the number of steps, and added a few extra feet for trimming and secure anchoring at top and bottom. Instead of accepting the pad sold at checkout, we ordered premium 2×3 rug pads separately, cut them into thirds, and placed them on the treads beneath the runner for extra cushion and grip.

Installing the runner
Installation followed the same basic method we used previously, with a few adaptations for these stairs’ profile. Our treads have a wide lip under the bullnose, so we stapled beneath that lip rather than through the bullnose itself. We used an electric stapler and a simple camouflaging trick: coloring staples ahead of time with a marker that matched the runner’s tones to reduce shine.

It took some experimentation on the first step to find the best staple placement for a tight hold and a hidden finish. We typically placed a staple just inside the binding under the bullnose, pulling the runner tight as we worked, and then ran staples across the step: two near each edge, one in the middle, and a couple spaced between. The runner’s texture helped mask the staples when placed over the middle of the tread.

We also stapled under the lip at the top of each riser and along the bottom edge of the riser above the quarter round, taking care not to drive staples into the tread face. Needlenose pliers were handy for removing any misplaced staples. Using a free hand to steady the stapler helped deliver straighter, tighter staples, and we checked centering with a tape measure as we progressed.

We ended up with about 18″ of excess at the bottom, which we trimmed with scissors and folded under about an inch for a tidy hem before stapling it along the bottom riser. The finished edge looks clean and professional.

We’re thrilled with how the stairs turned out. The runner improved safety and traction for Burger and for us, while also softening and unifying the stairway’s look. It complements the house’s original paneling and planking without being busy, and the natural sisal-look bridges the lighter downstairs pine and the deeper heart pine upstairs.


This view greets visitors from the front door, so a cozier, more welcoming stairway makes a big difference. The runner’s neutral tone also plays well with the gold hardware used throughout the house.


That’s our recent stair update. We have a few more interior and exterior projects to photograph and share soon. For those catching up, we’ve been busy the past few months and the stair runner is a simple, high-impact update that delivers both style and function.
*This post contains affiliate links, so we may earn a small commission when you make a purchase through links on our site at no additional cost to you.








