Objectales

Popular

Toilet Installation: Step-by-Step DIY Guide

featured 6495

Installing a toilet is one of the most approachable DIY plumbing projects you can tackle. We installed our first toilet when we became homeowners in 2006, and over the years we’ve replaced and reinstalled many more. It can feel a little messy or intimidating at first, but with the right tools and a clear plan, most homeowners can complete this job themselves. This guide walks through the entire process—from measuring your rough-in to finishing touches—using clear, practical steps and photos from several bathrooms we’ve worked on.

Side By Side Of John Installing Two Toilets

These instructions are useful whether you’re replacing a broken toilet, fixing a toilet that’s leaking or rocking, or reinstalling an existing unit after a remodel.

Tools & Supplies Needed

You don’t need many specialty tools to install a toilet. Gather these essentials before you begin so the job goes smoothly.

  • New toilet (or reuse your existing toilet)
  • Measuring tape
  • Wax ring kit (include a standard and an extra-thick option if uncertain)
  • Adjustable wrench or groove joint pliers
  • Flathead screwdriver
  • Rags and spare towels or blankets
  • Sponge, paper towels, and a small bowl or cup for water removal
  • Utility knife
  • Hacksaw (for trimming bolts)
  • White silicone caulk
  • Level (optional)
  • Gloves (optional)

If you plan to reuse your old toilet, a brand-new model isn’t required; the steps below include notes for reinstalling the same unit.

Steps To Install A Toilet

Read the full tutorial before you start to ensure you have all parts and tools. Here’s a quick overview of the process:

John Removing Toilet From Powder Room
  1. Measure your rough-in
  2. Choose and purchase a toilet
  3. Remove the old toilet
  4. Prepare the floor and flange
  5. Install the wax ring
  6. Set the toilet bowl
  7. Bolt the bowl to the floor
  8. Attach the tank
  9. Connect the water supply
  10. Complete finishing touches

Some steps are optional if you are reusing your current toilet.

Step 1: Measure Your Rough-In

The rough-in is the distance from the center of the floor bolts (or the flange center) to the finished wall behind the toilet. Most modern toilets use a 12″ rough-in, so measure from the bolt centers to the wall surface to confirm compatibility. Older or smaller bathrooms may have a 10″ rough-in, which requires a compact toilet designed for that dimension. Remember to include the thickness of baseboard molding in your measurement if applicable.

Tape Measure Taking Rough In Measurement By Toilet Bowl

Step 2: Purchase Your New Toilet

When selecting a toilet, consider these common options so the unit suits your bathroom and comfort needs:

  • Round vs. Elongated Bowl: Elongated bowls are generally more comfortable, while round bowls save space in tighter bathrooms.
  • Standard vs. Comfort Height: Standard bowl rim height is around 14–15″, while comfort or chair height is closer to 17″ for easier sitting and standing.
  • One-Piece vs. Two-Piece: Two-piece toilets (bowl + tank) are lighter to move and easier to handle during installation; one-piece models offer a sleeker, seamless look.
  • Single-Flush vs. Dual-Flush: Dual-flush models reduce water use by offering separate flush options for liquids and solids; you can also retrofit many toilets with a dual-flush kit.

Other choices include color, trim style, flushing performance, and specialty designs (wall-mounted, square-bowl, composting, etc.). Choose a model that fits your rough-in and the space available.

Step 3: Remove Your Old Toilet

Removing an existing toilet is essentially the installation process in reverse. Follow these steps:

  • Turn off the water and empty the tank and bowl
  • Disconnect the water supply line
  • Remove the tank (if two-piece)
  • Remove the bowl
  • Plug the flange opening temporarily

Turn off & empty water

Locate the shut-off valve behind or beside the toilet and turn it clockwise until it stops. Flush the toilet to drain the tank and bowl, then use a sponge or small cup to remove residual water.

Sponge Soaking Up Water In Toilet Bowl Tank

Disconnect the water line

Unscrew the supply line from the tank by turning the coupling counterclockwise. Expect a little water to spill, so keep a towel or bowl handy. You can leave the supply line attached at the wall if you plan to reuse it.

Hand Loosening Water Supply Line Under Toilet Tank

Remove the tank

If your toilet is two-piece, remove the tank by unscrewing the nuts on the tank bolts underneath. You may need a screwdriver inside the tank to hold the bolts steady while loosening the nuts. Set the tank on a towel or blanket to protect it from cracking.

Hand Unscrewing Bolts Inside Toilet Tank

Remove the bowl

Remove any bolt caps, then loosen and remove the nuts that secure the bowl to the floor. If caulk seals the base, score it with a utility knife. Rock the bowl gently side to side to break the seal of the old wax ring, then lift the bowl straight up and set it on a towel or blanket—placing it on its side or upside down helps avoid getting wax on the floor.

John Rocking Old Toilet Bowl To Loosen Wax Ring

Plug the flange hole

Immediately stuff a rag or towel into the exposed flange opening to block sewer gases and prevent debris from falling in. Remove the rag before installing the new toilet.

Step 4: Prepare The Floor & Flange

Clean the flange area thoroughly: remove old wax, caulk, and debris so the new wax ring and bowl will seat properly. Use a utility knife, putty knife, or screwdriver to scrape away wax. If the flange or surrounding flange bolts are damaged, replace them; otherwise you can reuse the existing flange.

Scraping Old Wax Ring From Bathroom Floor During Toilet Installation

Remove the old flange bolts and insert the new bolts supplied with your wax ring kit. These bolts usually slide into keyhole slots on the flange and can be held upright with plastic clips. If you’re reinstalling the same bowl, clean old wax off the bowl’s spud as well.

New Bolts On Toilet Flange With Rag In Sewer Hole

Step 5: Add The Wax Ring

The wax ring seals the connection between the toilet and the flange. Many kits include a rubber-reinforced wax ring and spare rings. If your floor height or flange depth is unusual, have both a standard and an extra-thick ring on hand. We recommend pressing the wax ring onto the underside of the bowl (wax side to porcelain) while the bowl is on its side—this helps ensure accurate placement.

Toilet Installation Wax Ring Kit With Bolts And Box
New Wax Ring On Bottom Of Toilet Bowl For Installation With Dog Sniffing

Step 6: Place The Toilet Bowl

Carefully lift the bowl and lower it over the flange so the bolts pass through the holes in the base. If needed, have a helper guide the bowl into position. Remove the rag from the flange before lowering the bowl. A useful trick is to slide short plastic straws over the bolts so they’re easier to see and align with the holes in the bowl.

John Placing New Toilet Bowl Onto Ground
Straw Trick On Toilet Flange Bolts

Once the bowl is positioned, press down firmly to compress the wax ring and create a seal. Some people sit carefully on the closed bowl to apply even pressure; just be cautious and steady when doing so.

John Sitting On Back of Toilet Bowl To Press Into Place

Troubleshooting placement

If the bowl goes down crooked, a bolt gets knocked over, or the wax ring becomes deformed, remove the bowl and start again with a fresh wax ring. Never try to reposition a toilet by twisting it on a compressed or damaged wax ring—replace the ring to ensure a proper seal.

Step 7: Bolt The Toilet Bowl

Place washers and nuts onto the floor bolts and hand-tighten them evenly. Alternate tightening each side a little at a time to avoid cracking the porcelain. Use a wrench to snug the nuts, but do not overtighten. Trim excess bolt length with a hacksaw, then install the plastic bolt caps.

Hand Tightening Bolt For Toilet Bowl Installation
Hacksaw Removing Excess Bolt Length On New Toilet

Step 8: Install The Toilet Tank

If your toilet is two-piece, set the tank in place over the bowl’s spud and align the rubber gasket. Insert the tank bolts with their rubber washers and hand-tighten the nuts underneath. Alternate tightening the bolts a little at a time and use a flathead screwdriver to hold the bolt from above if necessary. Check that the tank sits level and do not overtighten, which can crack the tank or bowl.

Hand With Screwdriver Adjusting Bolts In Toilet Tank

Step 9: Connect The Water Line

Reconnect the water supply to the tank and tighten the coupling by hand, using a wrench only for a final snug. Turn the shut-off valve back on slowly and let the tank fill. Flush a few times and check carefully for leaks at:

  • the water supply connection
  • the tank-to-bowl gasket and bolts
  • the base of the bowl around the wax ring

Tighten connections slightly if leaks appear at supply fittings or bolts. If water emerges under the bowl, the wax ring likely failed and must be replaced.

Step 10: Finish The Toilet Installation

Attach the toilet seat and make any desired adjustments to the tank’s flush mechanism. Run a final leak check, then apply a neat bead of white silicone caulk around the base to improve appearance and deter dirt and odors from getting beneath the toilet. Smooth the caulk for a clean finish.

Line Of White Caulk Around Base Of Installed Toilet

Bonus Step: Get Rid Of Your Old Toilet

Don’t toss a serviceable old toilet in the trash. Consider donating it to a local charity or resale shop, sell it if it’s in good shape, or recycle it through a facility that accepts porcelain fixtures. Clean it well before offering it for donation or sale.

Toilet Installation FAQs

Can I install a toilet myself?

Yes. This is a beginner-friendly plumbing project for anyone comfortable lifting 80–120 lb pieces and following step-by-step instructions. Two-piece toilets are easier to handle alone, but having a helper speeds up alignment and reduces strain.

Do I need a plumber?

If any part of the job feels beyond your comfort level—damaged flange, stubborn valves, or uncertain plumbing connections—hire a professional. Otherwise, with patience and the right tools, many homeowners successfully install their own toilets.

Should I caulk around the base?

Yes. A bead of silicone caulk around the base improves appearance, keeps the toilet from rocking, and prevents moisture and dirt from getting under the bowl—important for sanitation and preventing odors or mold.

Other Toilet How-Tos

Once your toilet is installed, you might find these related projects helpful: fixing a rocking toilet, converting to dual-flush, unclogging drains without chemicals, or troubleshooting backed-up lines. These tasks pair naturally with routine toilet maintenance and bathroom upgrades.

Kohler Memoirs Toilet In Marble Bathroom With Wall Molding
  • Choosing the right toilet model and height
  • How to stabilize a rocking toilet
  • Non-chemical methods to unclog drains
  • Upgrading or retrofitting flushing options

*This post contains affiliate links; we may earn a small commission at no additional cost to you if you purchase through links on the site.