How to Build and Install Built-In Cabinets: Step-by-Step
Built-in storage is one of the smartest ways to maximize a room—especially when it becomes part of the architecture. When we finished our attic and turned it into a bonus room, we wanted to take advantage of the recessed window niche. In this guide I’ll walk you through how we designed and installed built-in cabinets using stock cabinets—yes, it’s essentially an Ikea hack—so you can replicate the look and function in your own space.

This article focuses on the wall-to-wall built-in cabinets; we also created matching floating shelves for the niche, which complement the cabinets and complete the feature wall. The shelving is covered in a separate tutorial, since each project has its own steps and details.
Table of Contents
Step 1: Plan Your Built-Ins
The recessed nook in our bonus room was only 17″ deep, off-center within the room, and framed by two sloped ceilings—conditions that initially felt challenging but actually suggested a perfect opportunity for built-ins. Because the space was narrow, stock cabinet sizes and a careful layout could create storage without overwhelming the niche.

We used a kitchen-planning tool to test cabinet arrangements and visualized shelf ideas on the mock-up. After trying a few layouts, we settled on four standard base cabinets—each 30″ tall—spanning the lower wall, with a centered 20″ drawer base beneath the window to create a built-in “window seat” effect. Once the plan felt balanced, we generated a parts list and purchased the cabinets.

Step 2: Assemble Your Cabinets
Start by assembling the cabinet boxes. Follow manufacturer instructions and keep the doors and drawers off for now—it’s easier to handle, adjust, and level the boxes before adding fronts and hardware. This stage is a good time to confirm the spacing, alignment, and that the plan suits the actual niche dimensions.

Step 3: Build Cabinet Bases
Standard cabinet legs can be too tall for low windows, so we built custom bases from stacked 2×4 and 1×4 boards to achieve the exact height needed. These bases mainly serve as a sturdy backing for the toe kick or baseboard and provide a bit of protection if someone leans or stands on the lower cabinets. They also help set the cabinets at a consistent height across the span.
Step 4: Attach Cabinets to the Wall
Many modular cabinets hang on a metal rail system. Install a solid mounting rail into studs, then hang each cabinet using the manufacturer’s clips. Use a stud finder and a reliable level to position the rail. In our installation we also secured a horizontal 2×4 into the studs behind the rail to give the shallow 12″ cabinet boxes additional depth so they fit the 17″ niche more naturally.

Step 5: Add Filler Pieces
Once the cabinet boxes are hung (but not yet locked in), add filler strips between boxes to create a seamless, built-in look. Depending on your layout you may need wider filler pieces to compensate for an off-center window or unusual gaps. Cut pre-primed wood or purchased filler pieces to size and clamp them in place, then secure with small screws through the cabinet sides. Add vertical filler around the window if the rail would otherwise be visible.


Step 6: Add Final Filler Panels
The initial filler pieces usually sit flush with the cabinet box, but not with the door faces. To achieve a custom, continuous appearance, attach a second layer of thinner panels that match the profile and edge detail of your cabinet doors. For doors with a beveled edge, lightly sand the panel edges to replicate the look. Glue or nail these panels and fill any fastener holes before painting. We painted everything in a close-match white to the cabinet fronts for a cohesive finish.


Step 7: Install Toe Kick or Baseboard
Attach a continuous toe kick or baseboard beneath the cabinets to hide the base structure and give the installation a finished, built-in look. We nailed our baseboard into the 2×4 base we created earlier and trimmed it to fit the lower height dictated by the window. In most standard installations you can use unaltered baseboard stock.
Step 8: Add Countertops
We opted to keep the surface white to preserve a clean, cohesive feel. We used wood project panels sized to cover each cabinet section, primed and painted them to match the cabinet color, and then screwed them down from inside the tops of the cabinets. Allow the painted panels to fully cure before placing heavy items on them.

Step 9: Install Cabinet Hardware (Optional)
Adding matching pulls or knobs finishes the look and makes the cabinets practical to use. Measure carefully and install hardware consistently across all doors and drawers for a polished result. Once hardware is in place and any final paint touch-ups are done, your built-in cabinetry is complete.

After the cabinets were finished we added floating shelves around the window to complete the feature wall. Together the cabinets and shelves turned this blank wall into a functional, attractive focal point for the room.

More Built-In Cabinet Projects
If you’re looking for more inspiration, we’ve completed several built-in projects using stock cabinets and simple modifications. These approaches can adapt to bookshelves, dressers, wardrobe solutions, and other built-ins across the home.

- Ikea Besta hack into built-in cabinets
- Built-in bookshelves using stock cabinets
- Turning dressers into bookshelf bases
- Built-in dresser from a stock dresser
- How to make wardrobe systems look built-in
*Note: some tools and materials referenced may be available from common retailers; this write-up does not link to specific vendors.








